Used Equipment: Surface Combustion Super Allcase IQ Furnace – 36x36x72

Wisconsin Oven Gas-Fired Walk-In Oven

Stock #: V-1062

Manufacturer: Surface Combustion FMC #6487.

Type: Super 36 Allcase IQ Furnace

Serial No.: BC-43743-01

Heating Chamber: (4) sets of U-tubes

Maximum Fuel Demand: Natural Gas – 3750 / CFH

Maximum Temperature: 1950°F

Power: 480V, 3-Phase, 60 Hz

Working Dimensions: 36” wide x 36” high x 72” deep

Quench Tank: 5,000 gallon capacity

High flow 25,000 GPM, 30 HP quench agitation system
(4) Agitators, 7.5 HP each
Two-speed quench agitation
54 KW quench heating for 460V, 160°F operation; (6) heaters, 9 KW each
Air cooled quench oil cooler for 160°F operation, (1) fan
System #1 automatic internal handling (2 HP motors)
Heavy duty 5” diameter super alloy rollers and rails located on 21” centers
(2) Recirculating cast alloy fans, 5 HP each
Vibrating absorbing fan mountings
Proof of motion for fans
Door opening enlarged 1” at both sides
Atmosphere piping for high/low flow endothermic atmosphere to the furnace chamber (high flow during motions)
Natural gas enriching gas control valve
Waukee Flow meters: (1) each of endo, natural gas, air, ammonia, and nitrogen Automatic nitrogen purge system Heavy duty refractory insulation with arched roof that promotes atmosphere recirculation
13 ½” wall insulation for reduced heat losses
Recuperation & Automatic plunge cooling
Time delay for combustion system manual reset shut off valve
Two 2” shim stock ports one on each side of the furnace roof drop

Free-standing Nema 12 enclosure, 2-door
72”W x 18D” x 72”H, 200 Amp disconnect
Honeywell UDC2500 furnace hi-limit
Honeywell UDC2500 quench hi-limit
Allen Bradley SLC505 processing controller
CASEmate®Controlle with HMI Monitor
(2) SSI Gold probe with Type S T/C for carbon
Remote operator control station on quench tank

Motors: (1) Combustion air blower, 3 HP
(2) Recirculating fans, 5 HP each
(1) Rear handler, 2 HP
(2) Top cool fans, 2 HP each
(4) Agitators, 7.5 HP each
(1) Oil recirculating pump, 5 HP
(1) Heat exchanger fan, 2 HP

General: This unit is in excellent condition. The hoods, stacks, and vents are also included.

Download PDF Document: V-1062

NOTE: Equipment is sold “AS IS, WHERE IS” and buyer shall indemnify seller against and hold seller harmless from any and all claims, actions and damages arising out of the possession, operation, condition or use of the equipment. Seller suggests that you contact the manufacture for important information pertaining to safety and proper use and operation of the above equipment. For safety reasons, we request that you do not place the equipment into service until you have received current safety instructions from the manufacturer.

Specifications are taken with care, but are not certified. No warranties or guarantees, written or implied.

Used Equipment By Category
All Used Equipment | Box Furnaces | Car Bottom Furnaces | Continuous Annealing Furnaces |
Continuous HQT Furnaces | Continuous Tempering Furnaces | IQ Furnaces | Mesh Belt Brazing Furnaces
Pit Furnaces | Vacuum Furnaces | Charge Cars | Endothermic Gas Generators | Exothermic Gas Generators
Transformers | Freezers | Parts Washers| Material Handling | Scissor Lifts | Miscellaneous Parts

Contact our sales team at 734-331-3939 or at:

Welcome | About Us | Used Equipment | Appraisals | Terms of Service| Contact Us